• WTB / WTS / WTT ADS
    All Advertisements, including Want to Buy, Want to Sell, Want to Trade, Belong in the MARKETPLACE ONLY. Any new threads posted offering an item for sale, looking to trade or buy an item which are posted outside of Marketplace will be deleted without notice or warning. Existing threads will be moved to marketplace.
  • Marketplace Feedback Ratings
    The Marketplace feedback ratings system is now back. You can now leave feedback for your Buy / Sell / Trade transactions. Instructions on how to leave feedback ratings can be found HERE

Cetme Bolt gap

otis61

Well-known member
FALaholic #
26667
Joined
Feb 28, 2007
Posts
8,265
Location
N.W.coast
Feedback: 69 / 0 / 0
My daughters and son in law are making well over what I was making at their age, and investing more than I did. So, no real money for them when I take my long dirt nap. But, firearms on the other hand, are going to be quite abundant and varied. 😁;)
Most of these firearms they aren’t making anymore. They’ll be their own kind of nest egg.
 

AliYahu

Well-known member
FALaholic #
11084
Joined
Jul 1, 2003
Posts
4,160
Location
Texas
Feedback: 20 / 0 / 0
I have started working on my Cetme kit. To check the bolt gap, I slammed home the bolt a few times by hand. I don't have the stock mounted yet, so I didn't use the recoil spring to set the bolt in place. I still need to trim the rear of the Sarco receiver to get it to fit. My initial measurement is at 0.006. The max rollers I can find so far are +8. Changing the rollers will put me at 0.014 just inside the acceptable range of 0.012 to 0.020 inches. Is there an issue with using the +8 rollers that may cause issues in the future. I would rather it be closer to the upper end just in case.
I'm not sure that math is correct, each + size adds something like .0025" of gap. Going to 8.08 mm (+8) rollers would put bolt gap something like .026, way too large.
BTW you probably need to grind the buffer for clearance, not the receiver.
The CETME kits I checked were pretty tight on bolt gap - less than .010 - which is supposedly within military specifications.


Eli
 

Danziger

Well-known member
FALaholic #
88670
Joined
Jan 26, 2023
Posts
5,065
Location
The Woods
Feedback: 0 / 0 / 0
I'm not sure that math is correct, each + size adds something like .0025" of gap. Going to 8.08 mm (+8) rollers would put bolt gap something like .026, way too large.
BTW you probably need to grind the buffer for clearance, not the receiver.
The CETME kits I checked were pretty tight on bolt gap - less than .010 - which is supposedly within military specifications.


Eli
While your math is correct that would be for an inspect trunnion not a worn one requiring oversize rollers right.
 

jcduchock

Well-known member
Silver Contributor
FALaholic #
78867
Joined
Dec 4, 2016
Posts
5,854
Location
Central Ala.
Feedback: 28 / 0 / 0
Backing plate and stock fit now. Rollers ordered. Rollers are cheap and easy to replace. If it doesn't give me the correct gap, I'll just go down a size or two.
I'm doing this just like all the other first time kit builds. Go slow, take notes, ask questions, read, read and read some more. 😁 😁
 

adam762

Well-known member
Gold Contributor
FALaholic #
11334
Joined
Jul 28, 2003
Posts
6,497
Location
Washington Court House, OH
Feedback: 318 / 1 / 0
Of the two I have running right now, one took +6 and one took +8. Granted that took bolt gap to .017-.018" but that was before refinish and break in, which tends to bring it down a bit. Both rifles are smooth shooters. The upside to the barreled trunnions is the original barrel. The downside is the potential for larger rollers. Even if you're well equipped to press barrels, it's a lot of extra work compared to larger rollers. Remember if you rotate the barrel to repin, you're going to have to rotate the soldered on sight block as well. If your trunnion is already welded in, sight alignment will be a consideration.
 

adam762

Well-known member
Gold Contributor
FALaholic #
11334
Joined
Jul 28, 2003
Posts
6,497
Location
Washington Court House, OH
Feedback: 318 / 1 / 0
On another note, as others have said, the mod you'll need to do is to the recoil plate. The original CETME receiver did not have the reinforcing weldment in the back near the stock pins I don't think, while the G3 does. So, if you have a receiver with that weldment (and your G3 receiver will) you'll have to shave some material off the bottom sides of the plate so it fits inside the weldment. I made the mistake of adding the weldments to my first two rifles, that's how I know.
 
Top